Use este identificador para citar ou linkar para este item:
http://www.repositorio.ufop.br/jspui/handle/123456789/8834
Título: | Technological properties of ceramic produced from steatite (soapstone) residues–kaolinite clay ceramic composites. |
Autor(es): | Torres, Harlley Sander Silva Varajão, Angélica Fortes Drummond Chicarino Sabioni, Antônio Claret Soares |
Palavras-chave: | Kaolinite clay Soapstone residues Composites |
Data do documento: | 2015 |
Referência: | TORRES, H. S. S.; VARAJÃO, A. F. D. C.; SABIONI, A. C. S. Technological properties of ceramic produced from steatite (soapstone) residues–kaolinite clay ceramic composites. Applied Clay Science, v. 112-113, p. 53-61, 2015. Disponível em: <http://www.sciencedirect.com/science/article/pii/S0169131715001532>. Acesso em: 25 ago. 2017. |
Resumo: | Ceramic bodies (7.0 cm× 2.0 cm× 1.0 cm) of kaolinite clay and soapstone residuals collected fromworkshops in Ouro Preto and Mariana, Minas Gerais, Brazil, containing from2.5 to 97.5wt% steatite (soapstone) were prepared and firing at 500, 1000 and 1200 °C, for 2 h, in air. The linear shrinkage, compressive strength, water absorption and mass loss by heating were determined on the samples after heat treatment. The fired samples at 1000 and 1200 °C, with steatite percentages of 85, 90 and 95%, presented the best results for technological applications in ceramic industry. For these samples, the values of the compressive strength were higher than 10 MPa and those of water absorption varied between 8 and 22%, which means that the values of these properties are superior and inferior, respectively, to the reference values established by Brazilian Standards. The linear shrinkagewas lower than 6%, which is the maximum value established by the Pólo Cerâmico de Santa Gertrudes, in São Paulo State. These samples were chemically, mineralogically, and morphologically analyzed using ICP/OES, X-ray diffraction, Mössbauer spectroscopy, SEM and BET. Talc and kaolinite were the dominant minerals, followed by quartz, chlorite, magnetite and magnesite. When firing at 1200 °C, the talc changes to enstatite and the appearance of mullite, periclase, hematite, clinoenstatite and protoenstatite occurs. The partial fusion of the talc promoted an increase in the liquid phase diminishing porosity and, consequently, water absorption. This process and the combination with mullite and periclase, increased the strength, reaching the values of 78 MPa, which is much greater than the minimum value of 10 MPa defined by the Brazilian Standard 15270-1 (ABNT 2005) for application on structural ceramic blocks. |
URI: | http://www.repositorio.ufop.br/handle/123456789/8834 |
DOI: | https://doi.org/10.1016/j.clay.2015.04.016 |
ISSN: | 0169-1317 |
Licença: | O periódico Applied Clay concede permissão para depósito deste artigo no Repositório Institucional da UFOP. Número da licença: 4193050674777. |
Aparece nas coleções: | DEGEO - Artigos publicados em periódicos |
Arquivos associados a este item:
Arquivo | Descrição | Tamanho | Formato | |
---|---|---|---|---|
ARTIGO_TechnologicalPropertiesCeramic.pdf | 1,76 MB | Adobe PDF | Visualizar/Abrir |
Os itens no repositório estão protegidos por copyright, com todos os direitos reservados, salvo quando é indicado o contrário.